- 您现在的位置：买卖IC网 > Sheet目录323 > DV164131 (Microchip Technology)KIT STARTER PICKIT 3
Error Messages
PK3Err0029: Communication failure. Unexpected command echo response %x
received from PICkit 3.
See Section 8.3.3 “Debugger-to-PC Communication Error Actions” .
PK3Err0030: Unable to read/find firmware File %s.
If the Hex file exists:
? Reconnect and try again.
? If this does not work, the file may be corrupted. Reinstall MPLAB IDE.
If the Hex file does not exist:
? Reinstall MPLAB IDE.
PK3Err0031: Failed to get PC.
PK3Err0032: Failed to set PC.
See Section 8.3.2 “Debugger-to-Target Communication Error Actions” .
PK3Err0033: %d bytes expected, %d bytes received.
See Section 8.3.3 “Debugger-to-PC Communication Error Actions” .
PK3Err0034: This version of MPLAB IDE does not support hardware revision
%06x. Please upgrade to the latest version of MPLAB IDE before continuing.
Find the latest MPLAB IDE at www.microchip.com.
PK3Err0035: Failed to get Device ID.
See Section 8.3.1 “Read/Write Error Actions” .
PK3Err0036: MPLAB IDE has lost communication with PICkit 3.
See Section 8.3.3 “Debugger-to-PC Communication Error Actions” .
PK3Err0037: Timed out waiting for response from PICkit 3.
PK3Err0038: Failed to initialize PICkit 3.
PK3Err0039: PICkit 3 self-test failed.
For this error, the debugger is not responding:
1. Unplug and plug in the debugger.
2. Reconnect to the debugger in MPLAB IDE.
3. If the problem persists contact Microchip.
PK3Err0040: The target device is not ready for debugging. Please check your
configuration bit settings and program the device before proceeding.
You will receive this message when you have not programmed your device for
the first time and try to Run. If you receive this message after this, or immediately
after programming your device, please refer to Section 8.3.6 “Debug Failure
Actions” .
PK3Err0043: RS download failed.
PK3Err0044: AP download failed.
PK3Err0045: You must connect to a target device to use PICkit 3.
No power has been found.
1. Ensure V DD and GND are connected between the debugger and target.
2. Ensure that the target is powered.
3. Ensure that the target power is sufficient to be detected by the debugger (see
Chapter 10. “Hardware Specification” .)
PK3Err0046: An error occurred while trying to read the stopwatch count. The
stopwatch count may not be accurate.
? 2009 Microchip Technology Inc.
DS51795A-page 43
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
DV164132
KIT EVAL F1 FOR PIC12F1/PIC16F1
DV243003
KIT STARTER FOR SRL MEM PRODUCTS
DVA1001
ADAPTER FOR PIC16F716 18DIP
DVA1004
DEVICE ADAPTER 8/14/20DIP
E3R-D12GP-P
RELAY RCVR PLUG-IN DIMMER
E3R-R12-3HOTP
RCVR 3WIRE RELAY 120V
E3R-R12GP
RCVR PLUG-IN RELAY
E3T-MICFP-40
CONVERTER 4-CH SLT SENSOR
相关代理商/技术参数
DV164131
制造商:Microchip Technology Inc 功能描述:PICKIT 3 DEBUG EXPRESS
DV164131-XLP
制造商:Microchip Technology Inc 功能描述:KIT DEV PICKIT 3-XLP/NANOWAT
DV164132
功能描述:开发板和工具包 - PIC / DSPIC F1 Evaluation Kit RoHS:否 制造商:Microchip Technology 产品:Starter Kits 工具用于评估:chipKIT 核心:Uno32 接口类型: 工作电源电压:
DV164132
制造商:Microchip Technology Inc 功能描述:PIC12F1xxx/PIC16F1xxx F1 Evaluation Kit
DV164133
功能描述:电源管理IC开发工具 Energy Harvesting Development Tool
RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
DV164136
功能描述:开发板和工具包 - PIC / DSPIC PIC18F DEV Kit (with PICkit 3) RoHS:否 制造商:Microchip Technology 产品:Starter Kits 工具用于评估:chipKIT 核心:Uno32 接口类型: 工作电源电压:
DV164139
功能描述:开发板和工具包 - PIC / DSPIC Lo PIn Count USB Dev Kit (w/PICkit 3) RoHS:否 制造商:Microchip Technology 产品:Starter Kits 工具用于评估:chipKIT 核心:Uno32 接口类型: 工作电源电压:
DV17K3225T
制造商:SEI Stackpole Electronics Inc 功能描述:- Tape and Reel 制造商:SEI Stackpole Electronics Inc 功能描述:Var MOV 17VAC/22VDC 100A 27V 3225 SMD T/R